Contents
How to hotwire a motorcycle? It’s not as difficult as you may think. With a little know-how, you can have your motorcycle up and running in no time.
Checkout this video:
Introduction
Hotwiring a motorcycle is a skill that can come in handy if you find yourself in a situation where you need to start your bike without the key. While it’s not something that you should do on a regular basis, it’s good to know how to hotwire a motorcycle in case of an emergency. In this article, we’ll show you how to hotwire a motorcycle so that you can get back on the road in no time.
Tools and Materials
In order to hotwire a motorcycle, you will need a few tools and materials. First, you will need a screwdriver. Second, you will need a wire cutter. Third, you will need a voltmeter. Fourth, you will need a pair of pliers. Fifth, you will need a hammer. Sixth, you will need a set of wrenches. Seventh, you will need an electrical tape. Lastly, you will need a pair of gloves.
The Process
Most people who hotwire motorcycles do so because they have lost their key or their key is broken. While it is possible to hotwire a motorcycle without a key, it is not recommended as it can damage the ignition. It is also illegal in some states.
To hotwire a motorcycle, you will need:
-A screwdriver
-Pliers
-Wire cutters
-A length of wire
The first step is to locate the ignition switch. This is usually located on the right side of the motorcycle near the gas tank. Once you have found the ignition switch, use the screwdriver to remove the screws that hold it in place.
Once the screws are removed, you will need to use the wire cutters to remove the wires that are attached to the back of the ignition switch. There are usually two wires, one red and one black. The black wire is known as the ground wire and should be cut first. The red wire is known as the power wire and should be cut second.
Once both wires are cut, you will need to use the pliers to twist them together. Once twisted together, hold them in place and wrap them with a length of wire. Make sure that the connection is tight and secure before moving on to the next step.
The next step is to locate the spark plugs. The spark plugs are located on either side of the engine near the top. Once you have found them, use the pliers to remove them from their sockets.
Once they are removed, you will need to use the wire cutters to cut a length of wire that is long enough to reach from one spark plug socket to the other. Once Cut, thread this wire through both spark plug sockets and then twist it tightly around both plugs. If done correctly, this will create a spark that will ignite the fuel in your engine and start your motorcycle
Tips and Tricks
You’ll need a few tools to hotwire a motorcycle. A screwdriver, a pair of pliers, and a wire cutters or strippers. You’ll also need a voltmeter to test the wires for power. If you don’t have a voltmeter, you can use a test light or an illuminated multimeter.
The first thing you need to do is find the ignition switch. It’s usually located on the steering column or on the frame near the steering column. Once you’ve located the ignition switch, use the screwdriver to remove the screws that hold it in place.
Next, locate the two wires that go to the ignition coil. The positive wire will be red or orange and the negative wire will be black or brown. Use the pliers to twist the wire around the terminal of the ignition coil. This will bypass the ignition switch and send power directly to the coil.
Now, use the voltmeter to test for power at the terminals of the spark plugs. If there is power, then you’re done! If there is no power, then check all of your connections and make sure that they are tight.
Frequently Asked Questions
Q: How to hotwire a motorcycle?
A: The process of hotwiring a motorcycle is actually quite simple, and can be accomplished in just a few minutes with the right tools. First, locate the spark plug wires and remove the caps. Next, use a screwdriver to remove the spark plug from the engine. Finally, use a pair of needle-nose pliers to twist the exposed wire around the terminal of the battery.
Conclusion
In conclusion, hotwiring a motorcycle is not as difficult as one might think. With the proper tools and instructions, anyone can do it.
References
-Find an ignition switch. You will need to remove a few motorcycle parts to find the ignition switch. Depending on the model of your motorcycle, the switch will be in different locations. Once you have found the ignition switch, you need to take it out.
-Remove the wires from the back of the ignition switch. You will see three or four wires coming out of the back of the switch. You need to remove all of these wires.
-Strip all the wires that you removed from the back of the ignition switch. Use a wire stripper to strip about 1/2 inch off of each wire.
– twist each stripped wire around a pencil or another object that is about the same diameter as the wire. This will give you something to hold on to when you hotwire the motorcycle.
-Touch each twisted wire to one terminal on the battery.Touching all four wires to the battery at once will cause a spark and could damage your battery, so make sure that you touch them one at a time.-Start your motorcycle by touching two wiresto two different terminals on your battery. If your motorcycle has a kickstand, make sure that it is up before you try to start it.-Hotwiring a motorcycle is not recommended and can be dangerous if done incorrectly
